restart

arkadaslar mbox hakkında bılgı verebılecek olan varmı.yabancı peerlerde kullananlar cogalmaya basladı

UYDUTURK

mbox un acıklamalı yazarsan iyi olur
MBOX cesit ceşit ney NBOX ayrıca konuyu yalnış yere actınız,

UYDUTURK

-Added support for Kathrein (tested on AAF 1.5 and AAF2.0b image).
-For SH4 receivers change D line value in mbox.cfg.


D: { 3 }

//D: { x } for DBOX2
//x=0 -> disable
//x=1 -> enable dbox2 cw writing
//x=2 -> enable STAPI for IPBOX
//x=3 -> enable STAPI for Kathrein
//default disable

This is not a finished project but it's a start. (beta version)
Mbox is next generation Gbox.
With this version you can not Reshare cards (yet) !!!
You can add Newcs connections (no cs2gbox needed)
You can use your old cwshare.cfg (same D line or use the new format)

To start you need to start it like this:

cd /data/emu
./mbox.sh40

Don't forget to correct the settings in the mbox.cfg file (this must be in the same dir as mbox.sh40)
Set D to 3 for UFS910.


Note:
- restart mbox works only on a free channel or when rebooting. (will be fixed later)
- don't start first another emu. (start kahtrein with no emu then start mbox or start box with mbox)

+++++++++++++++++++++++++++++++++++++++++
Make sure when you boot your kathy that mgcamd is not running or started before.
Start kathy with no emu.

Make sure you have all files in the correct dir.

- mbox.sh40 and mbox.cfg ==> /data/emu/
- cwchare.cfg == > /data/****

Chmod 755 to mbox.sh40.


Then settings in mbox.cfg:

D: { 3 }
T: { /tmp/ }
K: { /data/****/ }
M: { 1 }
P: { /tmp/pmt.tmp }


Then open a telnet session and give these commands.

cd /data/emu
./mbox.sh40

Now it should run.

To stop Mbox create a fill mbox.kill and put it in the same dir as mbox.sh40.

touch /data/emu/mbox.kill


+++++++++++++++++++++++++++++++++++++++++
Mbox runs on:

- dreambox 70xx - Dbox2 => mbox.ppc
- dreambox 800 => mbox.mips
- linux pc => mbox.i386
- IPbox900/9000 - KathreinUFS910 => mbox.sh40
- Win32 pc => mbox.exe

Mbox is still beta and the REshare function is disable to test.
Mbox can handel locals if they are on Newcs. (don't forget to use the correct c-line)

Here it takes my local card that's on newcs. First i did only take it from Gbox server.
Then i added { 5 } at the end of the C-line.
Now it take first my local card.

C: { server_ip server_listening_port username password des_*** } { x } { xxxxyyyy:xxxxyyyy;......} { xxxx:xxxx:xxxx:.......}
C: { 127.0.0.1 15000 dummy dummy 01 02 03 04 05 06 07 08 09 10 11 12 13 14 } { 10 } { 0100006a:0100006B;} { 1420:A200:B302:}

[second brascet] -> { x } max. number ecms in buffer

[third brascet] { 0100006a:0100006B;} is used if you want to change caidprovid from what newcs detected to caidprovid to use with gboxx protocol so 0100006A will be 0100006B in gboxx protocol

[last brascet] -> forbiden SID pids



İNDİRR-UYDUTURK
ALINTIDIR,

BÖYLE DE VAR,

Mbox V02.07 softcam released




A new version of the Mbox softcam has been released, with a lot of improvements.


Mbox is the reincarnation of the popular Gbox softcam & offers support for Gbox cardsharing. You can use the mbox.sh40 binary for the UFS 910 (other versions are for PC, or Dreambox)

Changelog

07.09.2008

Minor newcamd code optimization.
Improved irdeto chid handling.
Now no need to select again channel on start ro read PMT table.
Fix minor problem when sending ECM.
No default path for mbox.kill, so now create mbox.kill file where T: path is.
Fix problem starting mbox without argument & with default mbox.cfg path /var/k e y s /